We have noticed this article relating to Tools You Need to Install a New Bathtub down the page on the web and concluded it made good sense to talk about it with you on my blog.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a bathtub isn't specifically brain surgery, however it does require solid plumbing, carpentry, and also sometimes, tiling abilities. Changing an old tub with a new one is additionally a reasonably challenging project. If the old bathtub is easily available, the task can move quickly; if you need to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. Make sure you have certified yourself for the work and also are comfortable trying it. Rather than hiring a professional to take over a halfway-completed project, it is better to think about using one before you start. Chances are you may require a professional plumber to make tube links.
This post will certainly assist you set up a brand-new bathtub in your shower room if you have actually currently acquired a brand-new bathtub as well as don't need to change the setup of your previous water supply pipes.
Your devices and also material checklist should comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be quite bothersome as a result of the restricted gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipes. When the supply pipes have actually been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washing machines are in place in between the tap as well as the sink. Protect the tap in place with the supplier given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind should be attached to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Making use of the two wooden boards under its feet, put the tub in the required position. The wood boards are handy in evenly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little points.
The following goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the supply of water as well as check all joints and new pipework for leaks and also tighten them if necessary. Load the bath tub as well as likewise examine the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the manufacturer's instruction manual. Tiling and also sealing around the bath tub ought to wait till the tub has been used at least once as this will certainly resolve it into its final placement.
Getting ready for the Installation
To start with, the sustaining frame provided with the bathroom needs to be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split a stiff seal, causing the water to pass through the wall in between the bathroom and the tiling, leading to problems with moisture and also feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and also cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched paper or soft rope. Remember to constantly load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can break rather early if you do not consider this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly offered on the market. It is advisable to fit the tiles using water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that report on Installing A Bathtub through an associate on our other web blog. Liked our post? Please share it. Let other people find it. I truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Quote & Schedule